Manitou Black Manual

1. Manitou Black 2004 Service Manual
2. Manitou Service Manual
3. Manitou Axel Elite 100 Manual

2004 SERVICE MANUALManitou Q shocks28209 Avenue Stanford, Valencia, California 91355661 257-4411 fax 661 294-4179 www.answerproducts.com04 Q SHOCK SERVICE MANUAL INDEXSectionDescriptionPage1INTRODUCTION32SETUP, TUNING, PERIODIC MAINTENANCE33GLOSSARY44COMPLETE SHOCK LESS HARDWARE55HARDWARE REMOVAL AND INSTALLATION56DU BUSHING REMOVAL AND INSTALLATION67AIR CANISTER88AIR CANISTER REMOVAL AND SEAL SERVICE99DAMPING SYSTEM1110TROUBLESHOOTING1211TABLE 1: FASTENER TORQUE REQUIREMENTS1312Q SHOCK SERVICE KITS14Contact InformationAnswer Products Customer Service Department28209 Ave. StanfordValencia, CA 91355Toll Free: (800) 423-0273Direct: (661) 257-4411FAX:(661) 775-1798E-mail:Web site: www.answerproducts.com04 Q SHOCK SERVICE MANUALPage 2PN 042132 REV NCSECTION 1: INTRODUCTIONThis manual is intended to guide the user through basic service of Manitou Q rear shocks.Service is supported by the identification of common parts and assemblies that have beenassembled into Service Kits. The purpose of this manual will be to describe conditions that maydrive the need for service and to provide installation instructions for the kits.Due to the time-consuming nature rear shock service, at this time our primary focus is to offerservice kits that minimize the amount of downtime and labor involved. As the program matures,and we are able to gather feed back from our customers, we may offer kits to a more detailedlevel.GENERAL WARNING: Rear shocks by design contain gases and fluids under extremepressure and warnings contained in this manual must be observed to reduce thepossibility of injury or possible death.

Following these instructions can help you reducethe risk of being injured. Any questions in regards to the information in this manualshould be directed to Answer Products Customer Service at (661) 257-4411.CAUTION: The Q Shock uses compressed air to provide fluid pressure in the dampingsystem and spring resistance.

These systems must be relieved of pressure prior toservicing. Failure to relieve air pressure could result in injury or possible death.CAUTION: The Q Shock uses precision machined aluminum and other soft alloy components.Using correct tools for assembly is essential to prevent damage.SECTION 2: SETUP, TUNING, PERIODIC MAINTENANCEInstructions for shock setup, tuning, and periodic rider maintenance is not covered in detail in thismanual. Please refer to the Manitou Q Rear Shock Owner's Manual (PN 042107) for thatinformation. If you did not receive a manual, you can download one at www.answerproducts.comor contact Answer Products Customer Service at (661) 257-4411.04 Q SHOCK SERVICE MANUALPage 3PN 042132 REV NCSECTION 3: GLOSSARY OF TERMSAir Canister – Can that holds the air spring air in an air shock.Bottom Out – Point at which a shock reaches full compression.Control Eyelet (C-End) – Eyelet that is on the rebound adjuster end of a shock.

The air canisteris attached to this end on air shocks.Damper Eyelet (D-End) - Eyelet that is on the damper body end of a shock.Damper Body – Section of shock that contains the damping systemDamper Shaft – Shaft attached to the damper piston that connects the two moving sections(damping system and control eyelet) of the shock together.Damping System - Controls compression and rebound rate (speed).DU Bushing – Teflon guide bushing pressed into the eyelets. Mounting hardware is inserted intothe DU bushings and rotates within the bushing as need by the suspension design.Eyelet – Found on each end of the shock, it is where the DU bushing and mounting hardware areand provides the connection between the shock and bicycle.Internal Floating Piston (IFP) - A floating piston that separates damping oil from the dampingsystem air chamber.Lockout - Found on QRL shocks. The Manitou lockout significantly increases the amount of loadrequired to compress the shock. The lockout does not prevent compression under load, onlyincreases the amount of load required to compress the shock.Mounting Hardware – Hardware that allows shocks to be mounted into the wide variety ofsuspension designs.Schrader, Air – Black in color, it is the valve for pressurizing the air canister in an air shockSeals: O-Rings - Black synthetic rubber with a round cross section.

Primarily used for fluidsealing.Seals: Quad Seals -: Black synthetic rubber with an “X” cross section, primarily used for sealingair.Seals: Wipers – Teflon ring, used for keeping debris out of quad seals, guiding the damperpiston, and providing support.Top Out – Point at which a shock returns to its full extension.04 Q SHOCK SERVICE MANUALPage 4PN 042132 REV NCSECTION 4: COMPLETE SHOCK LESS MOUNTING HARDWAREThe highest-level kit offered will be a complete shock without mounting hardware. These kits areoffered as a fast replacement where all that is need is to change out the hardware or dampingunit.Q Shock – Less Mounting HardwareSECTION 5: HARDWARE REMOVAL AND INSTALLATIONMounting hardware is used to mount shocks to the various frame configurations. Over time,hardware may wear between the mounting bolts or DU Bushing which will result in play in theconnection.Remove hardware using pliers as shown in Figure 1DU BushingEyelet.Figure 1Figure 2HARDWARE REPLACEMENTHardware should have a slight press fit into the DU bushing and can be tapped in place with arubber mallet or soft jaws in a vise.

Apply a small amount of thick grease such as Motorex BikeGrease 2000 (PN 85-0033) to the hardware before installation.There are virtually an infinite number of hardware combinations in use on bikes today. Whenordering hardware from Answer Products, It will be necessary to identify the overall eyelet width,eyelet width, and mounting hole diameter.04 Q SHOCK SERVICE MANUALPage 5PN 042132 REV NCHARDWARE REMOVAL AND INSTALLATION- (CONT.)1. Measure the overall eyelet width.2. Measure hole size. Current hardwareare designed to accept a 6mm or 8mmfastener.3. Measure eyelet width.SECTION 6: DU BUSHING REMOVAL AND INSTALLATIONDU bushings are press fit into the shock eyelets at each end of the shock.

The hardware fit intothe bushings and will rotate slightly within the bushing during suspension compression. DUBushings, like hardware, may wear over time.

Removal and installation is accomplished usingtool PN 85-6075.REMOVAL1. Remove hardware from the shock.2.

Insert unthreaded end of punch into theremoval tool first and screw in about half aturn.Punch04 Q SHOCK SERVICE MANUALPage 6PN 042132 REV NCDU BUSHING REMOVAL AND INSTALLATION (CONT.)3. Clamp removal tool in vise.4. Insert eyelet into tool.5. Use 6mm hex wrench to screw in punch,making sure that it is centered on thebushing. This will press out the bushing.INSTALLATION1. Place a bushing onto the threaded end ofthe punch and into the removal tool; screwin about half a turn.Bushing2. Clamp removal tool in vise.3.

Insert eyelet into tool.4. Use 6mm hex wrench to screw in punch,making sure that it is centered on thebushing and that the bushing is centered tothe eyelet.

This will press in the bushing.04 Q SHOCK SERVICE MANUALPage 7PN 042132 REV NCSECTION 7: AIR CANISTERWARNING: Manitou Q Air Shocks use compressed air to provide resistance tocompression in place of a coil spring. You must be certain that the air canister is relievedof all pressure prior to servicing the air system. Failure to relieve air pressure could resultin injury or possible death.Failure of an air shock to maintain air pressure is usually the result of defective or worn seals. Ifthere is suspicion of an air leak, the location can be isolated by spraying the air canister jointswith a mild solution of dish soap and water. Bubbles will form in from the area of leakage. Youcan also immerse the shock in water to locate the leak.Sealing of the shock is accomplished through a series if o-rings, quad seals, and wipers. Whenthe air canister is removed, these seals can be replaced from Seal Kit C.Seal Descriptions:O-Rings: Black synthetic rubber with a round cross section.

Used for fluid sealing.Quad Seals: Black synthetic rubber with an “X” cross section, used for sealing air.Wipers: White Teflon, used for keeping debris out of quad seals.Adjuster Eyelet Schrader1. For leaks at the adjuster eyelet or damperend of the air canister, refer to the detaileddisassembly instructions below.2. For leaks at the Schrader valve, release allair pressure and replace the Schrader valvecore or assembly as needed.3. If when you pressurize the air canister theshock collapses to its shortest travelposition, the shock has an air piston leakinto the negative chamber. Place the shockin the shock tester and extend it to its fulltravel. Depress the adjuster eyelet Schraderwhile the shock is extended under load.

If itremains in the full travel position, refer tothe detailed disassembly instructions belowfor instructions on servicing the air canisterand piston seals.Shock in Shortest Travel Position4. If the shock returns to the short travelposition, it is not serviceable and the entireshock must be replaced.WARNING: Attempting to service ashock with this condition could result ininjury or possible death.04 Q SHOCK SERVICE MANUALExtend to long travel and depress the aircanister Schrader ValvePage 8PN 042132 REV NCSECTION 8: AIR CANISTER REMOVAL AND SEAL SERVICE1. Failure of an air shock to maintain airpressure is usually the result of defective orworn seals.

If there is suspicion of an air leak,pressurize the air canister to 150psi from theadjuster eyelet Schrader Valve. Locate theleak by spraying the air canister and Schraderjoints with a mild solution of dish soap andwater or submerge in a bucket of water.Bubbles will form in from the area of leakage.2. Release All air pressure from air canister.Remove hardware as shown underHARDWARE REMOVAL ANDINSTALLATION. For leaks at the Schradervalves, release all air pressure and replacethe Schrader valve core or assembly asneeded. The core is removed using astandard core removal tool. The assemblyis removed by removing the core andunscrewing the assembly by inserting a3mm hex into the center of the valve.Air release Schrader valve3. Place adjuster eyelet in a vise using softjaws.

Using a rubber strap wrench toprevent damage, loosen the air canistercompletely04 Q SHOCK SERVICE MANUALPage 9PN 042132 REV NCAIR CANISTER REMOVAL AND SEAL SERVICE (CONT.)Damper Cap: DO NOT REMOVE4. Slide air canister away from the canistereyelet and remove.WARNING: Do not remove the damper cap.The damper system is under extremepressure.

Removal of the damper capwithout releasing damper system pressurewill result in the possibility of injury orpossible death.5. Replace o-rings, seals, and wipers in the aircanister and air piston. Air Canister Kit A willhave new seals installed as part of the kit. Alsoreplace the o-ring inside the canister eyelet.O-Ring, Seal, Wiper Locations6. Lightly grease the air piston, damper body,air canister seals, and inside the air canisterwith a thick grease such as Motorex BikeGrease 2000.04 Q SHOCK SERVICE MANUALPage 10PN 042132 REV NCAIR CANISTER REMOVAL AND SEAL SERVICE (CONT.)7. Slide air canister over the damper body.8. Lightly grease the air canister threads andinside the canister.

Screw the air canisterinto the canister eyelet. Due to pressure inthe damping system, it may be difficult tocompress the shock enough to thread thecanister onto its eyelet. If necessary, theshock test fixture can be used.SECTION 9: DAMPING SYSTEMCAUTION: The Q Shock uses compressed air to provide fluid pressure in the dampingsystem and spring resistance. These systems must be relieved of pressure prior toservicing.

Failure to relieve air pressure could result in injury or possible death.Q Shock damping system service requires special tooling and training that is unavailable at thistime. In cases where it is suspected that there is air in the damper or the damper body is leakingoil, the shock should be replaced.04 Q SHOCK SERVICE MANUALPage 11PN 042132 REV NCSECTION 10: Q SHOCK TROUBLESHOOTING CHARTSymptomSchrader valvesnapped off at baseAir loss from air springAir shock does notreturn to full travel buthas adequate airspring pressureHard top outHard BottomoutOil leak at base of aircanisterOil comes out of theAir Spring SchradervalveAdjusting reboundknob has no effect.Lockout does notworkPlay in shock eyeletswhen mounted in bikeCauseSolutionAir SpringReplace.

Manitou Black Super Suspension Fork This fork is very good condition and shows only light signs of use. It does have a some scratches and scuffs but nothing that effects the integrity of it. It has 90 to 125mm of plush dial adjustable travel.

It also has 1 1/8' Steerer tube that's 9.5' long and is Disc brake ready. SPECIFICATIONS: Suggested use: all mountain/xc Travel: 90 to 125mm, System: coil spring Adjustability: rebound. Travel Steerer tube: 1 1/8' threadless alloy Steerer tube length: 9.5' Stanchions: aluminum Lower tubes: Post mount/ 9mm QR Brake: disc only weight: 1890g with star nut Wheel Diameter: 26' Shipping charges include insurance I Ship Fast! Usually within 24hrs or the next business day after receiving payment and I'll combine shipping on most orders.

Feel free to email me if you have any questions. Want more pics or need something fast and view my feedback so you can bid with 100% confidence. IMPORTANT INFORMATION PLEASE READ BEFORE BIDDING: Shipping Costs: are for the postage plus shipping materials and delivery to shipping facilities.

This may include boxes. Bubble wrap, foam peanuts, labels, paper, printer ink, tape and fuel. International Buyers: Import duties. Taxes and other charges are not included in the item price or shipping charges. These fees are the buyers responsibility.

Also I will not falsify customs documents and claim lower values so please don't ask. Leaving Feedback: I will gladly leave feedback once the entire transaction is complete and it has been left for me. This is to protect me from feedback extortion and receiving unreasonable negative feedback.

If you have a problem. Please contact me and give me a chance to correct any issues before leaving feedback. Unpaid Items: that remains unpaid for 3 days will receive a payment reminder from ebays automated system unless otherwise agreed upon.

If no contact is made from the buyer within 5 days of the listings end the unpaid item process will be initiated. UP FOR SALE A GARY FISHER MOUNTAIN BIKE.

ALUMINIUM FRAME, TASSAJARA. 2006) 16' FRAME SIZE,COLOR GRAY(METALLIC) HAVE SINGS OF REGULAR USE. SCRATCHES AND PAINT CHIPS FOR REGULAR RIDING, ALL STICKERS HAVE MISSING PARTS. SEE PICTURES, MANITOU BLACK COMP FORK. FLUID FLOW DAMPING, 90-120 TRAVEL ADJUST, FOR DISK BRAKE SYSTEMS. EXCELLENT, MATCH FRAME COLOR, WEIGHS: 12 POUNDS.

FRAME AND FORK, ALSO HAVE SIGNS OR REGULAR RIDING. SCRATCHES AND SCUFFS, WHAT YOU SEE ON PICTURES IS WHAT YOU WILL GET, FEEL FREE TO ASK ANY QUESTION, FAST SHIPPING. SAME OR NEXT DAY AFTER CLEAR PAYMENT SHIP MONDAY TO FRIDAY. EXCEPT HOLLY DAYS, SHIP ONLY TO U.S. DO NOT SHIP TO ALASKA.

HAWAII OR PUERTO RICO, NO INTERNATIONAL SHIPPING, MONEY BACK GUARANTEE IF YOU ARE NOT COMPLETE SATISFIED. Manitou Black 100mm travel suspension fork For 26' wheels. 9mm QR Long 9 1/2' steer tube. No crown race included 74mm post mounts for disc brake only Fork has about 6 seasons of use. Lots of miles Works fine.

Smooth, stanchions are in great shape(shown in pics) couple small marks Lowers/decals show lots of scratches/surface dings. No damage that would affect performance Crown shows normal rub marks and scratches from use No oil leak or air leak Weight is 3.7 lbs on my scale Shipping is standard USPS to the lower 48. AK/HI costs more, no international Please review my feedback. Still 100% positive Thanks for looking. Email me with questions or for more pics/etc. Used circa-2004 Manitou Black Super front mountain bike fork with SPV technology.

Adjustable rate(via air pressure) and rebound damping. Has probably 1500 miles of trail riding and was working when removed from my prior Giant mountain bike. Medium level of scuffing. Scratches and dings. Low reserve, just trying to clear out my garage. On May-20-13 at 07:33:31 PDT.

Seller added the following information: Update 5/20: The fork has a 7.50' long steer tube. 3j.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fuk%601d72f%2Bij%7Fil7g%3E3j-13ec553cae9-0xf7. GO SHOP NOW SELL YOUR GEAR POLICIES RETURNS ABOUT CONTACT Powered by Description Manitou 32mm Stanchions Fork Uppers These 32mm 1.5' Fork stanchions are ready to get your fork back up and running again. Condition NEW Never mounted/ Never used Light scuffing from storage Specs Brand: Manitou Model: 32mm Stanchions Size: 26 inch Stanchion Length: 295 mm Stanchion Size: 32 mm Steerer Tube Diameter: 1.5 inch Steerer Tube Length: 252 mm Weight: 985 grams All items come as pictured unless otherwise noted in the description.

You may be busy when the auction ends so place your bid now to ensure your chance to win. Check our feedback to bid with confidence and check our other auctions for similar products. New hard to find items are hitting the auction block daily so save our seller id and check back for future deals. TPC# BatsA10-2592-154596-TW. PHOTO# B 4/5/13 About Shipping Payment Returns OUR STORY While living in his Volkswagen Bus and only the task of riding a bike on his to-do list. Nick Martin began a simple mission: Sell all of his worldly possessions on eBay.

Minus his bike and his bus. Nick sold everything. Fast forward 8 years to today and we present to you. The Pros Closet. Located in Boulder Colorado, The Pro’s Closet has become the nation’s premier eBay store specializing in reselling new and used cycling gear.

If you are looking to sell your bike. Components, clothing or accessories, we are here to help! We cater to clients both locally and nationwide offering pickups, consultations, expert advice and more. We are an avenue for anyone, athletes, teams, shops, reps, companies, you) to free up space and put your unused product in the hands of people who will give it a second life. Buy something that already exists. It’s the greenest way to shop.

OUR PROCESS Orders are processed and shipped within 1 day of payment(excluding Saturday/Sunday) We reserve the right to choose the most efficient carrier for your order at the time of shipment. LOCAL PICKUPS FREE Local Pickup in Boulder. Local payments must be ma. Manitou Black Elite Air 80mm Blue Disc or V Brake Mountain Bike Suspension Fork. Thank you for your interest in this quality fork. It served well on a Moots YBB from 2002 that was seldom ridden. The steerer is cut to.

There is some oil on the compression cap and the compression dial does not seem to affect the feel. The air side holds well.

The fork is free of damage and the sliders are clean and free of scratches. Thank you for your interest. Please view our other listings for more High Peak Deals! Used but in good condition as you can see from the pics.This fork is 120mm travel and can be tuned down to 110mm. 100mm, or 90mm. Steer tube is 8 1/2' long. I put new Enduro Seals on it last year but they leak now.

You can get the kits here on ebay for $15. Other than the leaky seals it performs very well. Stanchions are in good shape with only a couple of tiny nicks. Normal 0 Refund Policy.

The refund will be less any shipping and handling charges and Ebay fees incurred by the seller. If an item is grossly misrepresented. A full refund will be given. Payment Policy. Payment is due within 24 hours of auction close.

Buy With Confidence Manitou Sherman Bicycle Fork 150mm 1 1/2' Steer 20mm Thru Axle Inlcuded Black. Powered by DESCRIPTION Manitou Sherman Bicycle Fork Condition Item Condition: 3 out of 5. Looks to be in great condition.

No major damage or signs of wear. Limited marks and very little signs of use. Condition unknown but seems to be fully functioning. Due to age may need a tune and to be serviced. Item Condition Scale: 5: New/Mint Condition.

No signs of use. May or may not come with original packaging. 4: Like New/ Excellent condition. No wear but minor signs of use evident on close inspection.

Item is in perfect working condition. 3: Very Good Condition.

Item is starting to show signs of wear but is not damaged in any way. Minimal wear and well maintained. 2: Good condition.

Obvious signs of use like rub marks. Scratches, tears. But item is in good working condition.

Item is worn but still has plenty of life left. Some items with minor damage will qualify. 1: Fair condition. Item has scratches. Rub marks, chips, dents, tears, etc.

That show obvious signs of use. Items with more serious damage will generally be“fair. Specifications Stanchion Length: 150mm 1 1/2' Steer Steer Length: 230mm NO Crown Race Inlcuded 20mm Thru Included 26' Wheel Size Disc Brake ONLY 5.5Lbs All items come as pictured unless otherwise stated in this description.

Thanks for visiting Gear Rush. We hope you'll be back. PAYMENT Paypal is our preferred method of payment.

All in state residents within our state will be charged state and/or local sales tax at the time of checkout. Payment must be received within 7 days of the close of auction. If payment isn't received within 7 days.

The auction will be revoked and a Non-Paying Bidder alert will be filed. SHIPPING Packages are usually shipped within 48 hours of payment receipt(excluding Saturday/Sunday) All orders are shipped via UPS.

FedEx, or USPS and we reserve the right to choose the most efficient carrier. A note about free shipping.

We wish that we coul. Packed with features such as Rapid Travel Wind Down no spring rate change travel adjustment. Our TPC Lockout damping system, and the latest generation Reverse Arch magnesium casting, the new Black Platinum has a Thoroughbred’s pedigree at a workhorse price. Elsewhere in the line, the Super offers the same high-end damping system mated to a significantly lighter air spring. Frugal and discerning riders, look no further.

Hold air with no leaks. In great working order. 200mm on the steerer tube. Manitou Black Elite 100mm 120mm External Travel Adjust Coil Spring 26 Fork TPC One of the most versatile forks on the market.

It contains one-switch instant travel adjust, coil spring internals and an excellent damping system TPC. 100mm or 120mm Rapid Travel Adjust Spring Coil. Excellent fork. Still works very well. Rubber seals and boots are in good shape.

Super stiff from the magnesium lowers and Reverse Arch. Steerer tube is straight 1 1/8' and measures 7 3/4' long. Star nut is installed and a crown race is included(though it may not work with your headset) There is a very shallow mark on one of the stanchions but it does not affect function.

All knobs are in good condition and adjustments work as they should. Travel is smooth and quiet as it should be. 9mm QR dropouts. 100mm hub spacing. Owner's manual can be found online.

Made in the U.S.A. Specifications Travel: 100mm or 120mm Rapid Travel Adjust; Actual Weight: 1831g(pretty light for an adjustable 120mm coil sprung fork) Steerer Tube: Aluminum; Crown: New Forged Aluminum. Hollow, Black Anodized Finish; Stanchions: 30mm Anodized Aluminum; Spring: Coil; Damping: Quick Range TPC; Outer: RA(reverse arch) Technology Magnesium; Lubrication: MicroLube; Adjustments: Preload.

Rebound Damping, Compression Damping, Rapid Travel Adjust; Color: Black Other: V-Brake boss option. Post Mount Disk brake mounts, Mini-boots with wipers. This fork is one of my favorites.

Beside the awesome looks. It is super light weight, it is still one of the lightest Rock Shox ever produced and the suspension is very smooth with the titanium inner tubes.

As you can see the lock out is included. It works also great!

The fork has got only on one SID decal some very little tiny dents on it. But you could also simply replace the decals; visually the condition of the whole fork is in my opinion still 8 out of 10 after some many years! I am always careful with all of my expensive bike stuffs. This nice rare fork in this beautiful colour/ color with carbon is really an collectors' item.

So it would not be sold for a low price for this excellent condition. But i hope i could find the new owner for this beauty: this fork would suit any other frame colors perfectly! The steering tube is by the. Way 23.5 cm/ 9,25 inch long. Please pay attention and read this before you bid: This is a private sell and no return is accepted.

World wide shipping with tracking barcode. I would NOT ship it to France and Italy and maybe also not to some other countries! And also if the bidder has not much positive feedbacks.

I would consider to refuse selling this fork to him. So first of all, please let me know about you before you bid, thank you for understanding and for reading this. Happy bidding: 336.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Fvo%7B%3Dd70f%2B%3E336-143d5faea2e-0xf5. 2004 Manitou Skareb Elite Suspension Forks- Includes original owners manual/leaflet- Travel: 80mm Steerer size: 1 1/8 Steerer length: mm Brake mount: Post mount disc brake& Canti rim brake This is a set of Manitou Skareb Elite suspension forks in very good used condition and perfect working order.

They compress and rebound perfectly well. The adjustment also works as expected. The seals do not leak. There are no marks to the stanchions, or any major damage to the forks. There are only light signs of use.

As you can see from the photos these forks look nearly new. Please refer to the photos to get a good idea of the condition. All the photos in this listing are of the actual forks for sale. Building a bike? Please check out my for more bike parts! I'm not looking to make a profit from postage costs. So I'm happy to combine items.

When posting. All my items are from a smoke-free. Pet-free home If you have any questions. Please do not hesitate to ask. This is a used Manitou Black Elite 90-120mm adjustable travel with the'Rapid travel wind down' knob on the top of the right stanchion. This is a great fork which functions perfectly and has a very plush ride.

Spring ideal for somebody 150-190 lbs. In tended as a Cross Country/All Mountain fork. NOT intended as a dirt jumper fork.

9mm dropouts Magnesium stanchions Disc Brake 8' Steerer tube 1 1/8 threadless RTWD travel adjust External rebound adjustment I rode this with a 26x2.35 BHT- 3 tire and there was ample clearance. Could possibly fit up to a 2.4. New fork oil and enduro seals wouldn't hurt it but it functions perfectly well as is.

Thanks for looking. Lightly used 29er 100mm travel fork(downward convertible to 80mm if desired- see online manuals) Steerer tube has been cut to 7' Star nut installed. With a history that dates back twenty years. Manitou’s Tower Expert marks a welcome return to form from one of the oldest brands in mountain biking. Headlining the companies 29er cross country fork line the Tower range replaces the older Minute line. Weight: 4.2lbs/ 1906.8g, Spring: ACT Air, Spring Rate: Soft, Bottom Out: Rubber Bumper, Steerer: 1 1/8' Aluminium Crown: Forged Hollow Crown, Crown Finish: Black Ano, Offset: 48, Compression Damping: TPC Technology. Absolute+, Rebound Damping: Adjustable TPC, Adjustments: Air.

Compression to Lockout, Rebound, Leg Diameter: 32mm, Leg Material: 7050 Straight Wall AL, Wheel Size: 29' Brake: Post Mount, Crown to Axle: 490/ 510/ 530, ACT. AIR: Atmospherically Controlled Tuning- Utilizes air to set preload/sag for wide range of users. This user friendly system is maintenance free and forgiving. With simple user input charts on the rear.

Features air pre-load adjustment. TPC(Twin Position Chamber) Providing 4-Dimensional Compression Damping; The velocity dependant circuit responds to the terrain while the Pressure Dependant Circuit flattens the bumps. The Energy Dependant Circuit activates on big hits while providing unmatched small bump sensitivity and the Position Dependant Circuit creates a bottomless feel. ABSOLUTE+: Velocity/Pressure Dependent System; Compatible with MILO remote lever. Absolute+ Switches between velocity dependent to pressure-dependent based on adjuster position. With an eight-position dial for compression rate-adjustment, it achieves lockout feel at maximum adjuster position, and plushness and control with pedalling efficiency. Fork came stock on a 2002 Giant XTC NRS 2.

One side oil(uses 5 weight) The other a coil. For 26' wheels. Disc brakes post mount.

The oil is all drained out but a few small drips are possible. Fork was cleaned but coil is still greased with new Bob Wood bike grease from when I took the fork apart.

I am not sure if replacement parts are available anywhere. They are no longer available from Hayes/Sram(who bought out Answer Products Inc) May not be able to fix it or use it'as is' So buyer should assume it is just for parts. The steerer tube(I think is it steel) Is 1-1/8th' threadless, length of 198 mm(7-13/16' or 7-3/4' without race on. Never cut any shorter since it was purchased. I will try to answer questions about the condition of the uppers. Lowers, or crown as best I can.

They look to be in good useable condition. With no bad damage. The upper tubes(red) have lots of wear in the spots where the brake cable was rubbing the fork(see pic) Not sure about the condition of the coil. It is from 2002, so has had much use. The small parts that are separate are: a small metal spring that is bent. Small metal washer, flat wide metal washer that is bent, small metal clip, and a plastic piece with the width to fit inside the upper tubes. Includes fork.

The 5 separate parts, and an owner's manual sheet that has some info on checking oil level. Buyer pays USPS shipping. Ships to USA only. Paypal payment only.

Payment due in 3 days. 2002 26 in WHEEL BICYCLE MANITOU ELITE LE FORK 8 1/4' Long 1 1/8 THREADLESS STEERER Manitou Black Elite LE Suspension 26 inch wheel fork with V Brake Bosses And Disc Brake Post Mounts. Threadless Steerer measures 8 1/4' Long. With a star nut installed. Ext Adjustable 100/ 120 mm travel. Dropouts measure 100 mm wide. Good Condition.

Some Slight Cosmetic Scratches and Sticker Wear. I am too heavy for it at 195 pounds. Best for 175 pounds and less. Can send eManual for this. SHIPPING Terms Also Note: This NON- Fragile Used item will be shipped in Eco- Friendly Used ReCycled Packing materials. Winning Bidder will receive eMail generated from Paypal with all the shipping and tracking info and a subject line something like this: Your purchase will be shipped by PayPal Shipping with U.S. Postal Service.

I will NOT ship this. Item Worldwide/ Internationally. I am not responsible for uninsured items that were lost or damaged in the mail. If you have questions please ask them before bidding. Thanks for Looking.

Good condition Manitou Black Super Air SPV Evolve 100mm Fork. Everything seems to work well. I removed the SPV valve to make sure it was working and it seems fine. I refilled it with fresh oil.

Both sides have been holding air just fine for the last couple of days. The damping and rebound seem to be working well when I push down and release the fork. This is an older fork and I have not had it on my bike for a long time. It has about 2 seasons of use.

Maybe less, and has been in storage since. Because of this, it is being sold as-is with no returns. I am not able to test it further since it is not installed on a bike. Please look at the pictures closely and ask any questions before buying.

This is actually a Manitou Black Elite 80/100mm fork. The only issue with it is that it does not size down to 80mm. It's currently a 100mm fork only. If you're into tinkering you can probably tear it down and figure out how to make it work at 80 again. But who really needs 80 with a fork like this? It's in really nice shape actually.

Missing a few stickers but the scrapes are minimal and upper legs are clean. I don't think this fork could even have more than 100 miles on it. Took it off a bike a bought and never used it much after that. 9' steerer tube so plenty of length to work with. There is a King race installed.

I will remove it or leave it for you is you want it. Fork is disc only. No Vee brake bosses No international bidders please. Lower 48 only. Shipping is 20.00 Fedex ground. Manitou Black Elite Fork 26' wheel fork 100mm suspension Straight 1 1/8' x 7 5/8' 194mm steer tube Reverse Arch magnesium casting Hollow forged aluminum crown 30mm Aluminum Upper Tubes TPC compression and rebound damping with semi-bath lubrication Disc brake specific USED- Smooth stroke. All adjustents are working well, good condition This is a Manitou Black Elite fork with a new retail value of $400(in 2006) I will send out immediately after payment.

I am an experienced bike mechanic of nearly 20 years. If you receive the item and have questions or concerns regarding it or questions with installation please feel free to contact me. I will do my best to assist you. Thank You& RIDE ON.

Wayne- 715-551-7210. Shipping US $20 Canada $60 All other countries $80 Please contact me for a combined shipping invoice for multiple items.

Be sure to add me to your favorites list Wisconsin sales include all applicable sales taxes Powered by The free listing tool. List your items fast and easy and manage your active items. Up for grabs is a Manitou Black suspension fork. Produced in 2002.

This is for 26' wheeled bikes, it has mounts for both disc and rim brakes. The steerer is 8 1/2' long, it's 1 1/8' in diameter. The fork operates smoothly, and is free from any damage, other than the typical minor scrapes and scratches encountered on the trail.

It has lock-out, but it does not work. It's a great way to replace or upgrade your worn or damaged fork without spending much money. Get it while you can! Thanks for looking, and be sure to check out my other items! Used but in excellent condition as you can see from the pics. This is a V-Brake or rim brake fork.

It will not work with disc brakes. Steer tube is 8 3/4' long. Starting bid is $29.99 There is no reserve. Refund Policy. The refund will be less any shipping and handling charges and Ebay fees incurred by the seller.

If an item is grossly misrepresented. A full refund will be given. Payment Policy.

Payment is due within 24 hours of auction close. Normal 0 false false false EN-US X-NONE X-NONE On Dec-08-13 at 13:32:35 PST. Seller added the following information: 254 mm long according to my metric ruler. Manitou Axel Forks in Silver& Black 80mm Travel QR 1 1/8 Steerer Manitou Forks Manitou Axel Elite Forks In silver and black They are in good condition Stanchions are good Travel is 80mm Have post mount for disc brakes The steerer is 1 1/8 and is 165 mm long They have quick release dropouts Nice quality forks Please check my feedback and terms to buy in confidence Feel free to ask questions Please make sure payment reaches us within 5 days.

If this is not possible then please get in touch before purchasing so we can come to a agreement I post items from Monday to Friday. Sorry no postage on Saturdays as it effects my riding time. The charges are listed below. I will not send high value items on a untracked service. Any items paid for by 1pm will be dispatched the same day Insurance is included in all quoted prices The item will be posted. Within 24hrs of payment clearing. If you are at all unhappy with your purchase please before leaving feedback get in touch and give us a chance to rectify the situation We are a small company specialising in high quality mainly pre owned Downhill and Freeride mountain bike parts.

Most of our stock is not listed on ebay so if there is something you are after please get in touch. Please feel free to message us through the ask seller question link or if you need to talk to us you can call or text Tel: 79.

Email is niall@fizbiz.biz. NOT AN EXPERT ON THIS ITEM. Item pictured is for sale as is.

Manitou Black forks for mountain bike. Item is clean with very few scratches and bumps. This is not a beater! Thank you for looking. IF YOU HAVE LESS THAN 10 POSITIVE FEED BACKS I WILL DELETE YOUR BID UNLESS YOU ASK FIRST OR I HAVE DEALT WITH YOU PREVIOUSLY!

FOR SOME REASON NEWBIES JUST HAVE NO PATIENCE WHEN SOMETHING IS SHIPPED ECONOMY THEY EXPECT IT TO BE THERE YESTERDAY! JUST GO ON TO THE NEXT LUCKY SELLER! LOWER 48 SHIPPING ONLY I DO NOT SHIP OUTSIDE THE U.S. NO INTERNATIONAL SHIPPING. IF YOU BID AND DO NOT HAVE A US ADDRESS YOUR BID WILL NOT BE HONORED NO IF’S AND OR BUT'SDON’T WASTE YOUR TIME OR MINE! IF YOU FEEL AS THOUGH YOU WANT THE ITEM THEN HAVE A FRIEND OR A RELATIVE OR A U.S.

BUYER SERVICE BUY IT AND SHIP IT TO YOU. PLEASE LET ME KNOW BEFORE YOU BID'. 1) YOUR PAYMENT IS REQUESTED WITHIN 3 DAYS OF AUCTION ENDING.

FAILURE TO COMMUNICATE REGARDING YOUR PAYMENT WITHIN 3 DAYS WILL BE AN AUTOMATIC COMPLAINT TO E-BAY& I WILL RE-LIST THE ITEM& YOU WILL NO LONGER BE WELCOME ON MY SITE. If an issue arises that prevents you from meeting this payment requirement. Please contact us immediately. We’re always willing to work with an honest buyer who has experienced an unexpected difficulty. I report ALL NON PAYERS so if you are not going to pay.don't buy. If you have a problem and need more time, please ask as I will work with you, but deliberate non payers and non communicators will be reported. 2) I pack your purchase with the utmost care and will have it in the mail as swiftly as I can!

I do not ship on Sat. I am happy to combine shipping whenever possible unless the items are two large to combine or very fragile. Shipping is more for Hawaii. Alaska unless it is shipped in a USPS flat rate box. Don't ask me to adjust my shipping charge, it is what it is! If it seems out of line, don't blame me, blame your postal service! Shipping does not include insurance but we highly recommend it.

Manitou Black Elite Forks Steerer is 195mm with star nut fitted. And a marin headset Removed from my marin due to buy some long travel forks The forks have a few marks on the lowers to sticker and paint. Stanchions have no scratches but as with all used forks you get some wear to the coating. Overall I would say these were excellent used condition. Not sure when they were last serviced as they came on a second hand bike. So would recommend a service although they work fine CASH ON COLLECTION ONLY NO PAYPAL No longer posting high value items as I wish people to view and test items before paying. To ensure they are happy.

Up for sale is a 2014 Manitou Dorado Expert Fork. Used one season. 2 small scratches at bottom, normal for DH fork.

Reason for sale is because I bought the new Rockshox WC. Wanted to try new forks and decided to try something new for next year. Steerer tube is cut to 6 inches. No scratches on stanchion. Will come with Original Box.

Manual, Manitou Shock Fork and extra bottle of Bath Oil I weigh 230 lbs and with the right sag I never bottomed out the fork. Rode it ONLY at mountain creek bike park in Vernon.

Inverted design is KNOWN to leak, so some leakage at the seals is normal and currently present but does not hinder any performance of the fork. It can be installed and used without any issues. It was on a 2014 Demo 8.

Previously stated, 2 small scratches at bottom from brushing a rock. Some MINOR cable rub. Otherwise perfect. Also this will ONLY fit a 203 mm size rotor.

Will ship with air pressure fully out. Included fork pump will be included for you to tune yourself. Informatin from Manitou's Site: The new Dorado is an engineering masterpiece. Inverted construction, dual-chamber air spring, TPC+ damping(with independent high- and low-speed compression) hydraulic bottom-out and top-out, and Manitou’s patented HexLock 20mm thru-axle add up to the most advanced downhill fork ever. PRO, EXPERT, Weight Lb/ grams 6.82/ 3096, Travel 180. 203 Internally Adj.

29'er 175mm) Spring Air, Spring Rate n/a, Bottom Out Hydraulic and Rubber Bumper, Steerer 1 1/8' Aluminum, Crown Forged Hollow Bore, Crown Finish Matte Ano Polished, Offset 49.55, Compression Damping TPC+, Rebound Damping Adjustable TPC, Adjustments Air Compression(High Speed and TPC+) Rebound, Leg Diameter 36mm, Leg Material Aluminum, Wheel Size 26' 27.5' 29' Brake Post Mount, Axle 20mm Hex TA, Crown to Axle 567/ 591, Colors Black Ano. A Manitou Black Elite 80-100mm travel suspension fork in very good condition. 1 1/8' x 6 3/4' steerer tube. Rebound control, disc or v-brake compatible.

Used items will usually have scuffs. Scratches and other signs of use.

Please examine the photos carefully before bidding, considering them part of this description. Fast shipping, let me know if you have any questions at all. Combined Shipping: If you purchase more than one item at the same time.

Just pay the shipping for each item. I will pack the items together and refund the difference between what you paid for shipping and the actual shipping cost. Bike frames and wheels/wheelsets are not included in this offer, but must be shipped separately. I'm the original owner of this 2013 Manitou Tower Pro 29er fork that is very lightly used.

My fox had a warranty issue so I bought this as backup and was very impressed with it's performance. Tapered steertube. 15mm thru axle, rare black color, 120mm length. Steerer tube is a bit over 7.5 inches and has star nut installed. Only selling to buy a fat bike.

Some very light scratches on lowers. Uppers are perfect. Cable wear on top of crown(should have put some tape) Very little use. Maybe ten easy rides total. Rebuilt Manitou Black Elite 80-100mm MTB Bike Suspension Fork Disc+Rim-Brake mounts for 26' USED- 2014 REBUILT- TESTED and PERFECT WORKING CONDITION Paint shows signs of age and use.

Does not impact function. For 26' wheel 1 1/8' Steer tube. 8 1/8' Long Adjustable 80mm-100 mm of travel Rebound and Compression adjust Standard quick release drop-outs Post mount disc brake mounts 1779g(3lbs 14.75oz) Actual Weight! Some decals removed. Handful of scratches, scuffs, does not impact function. See pictures. 1 1/8' MANTIOU SUPER BLACK SPV SUSPENSION FORK FOR MOUNTAIN BIKES Item Description Here is a nice Manitou Super Black SPV suspension fork for mountain bikes.

The fork has a 1 1/8' steerer tube with a length of 7 7/8 inch. This is a no reserve auction. WINNER TAKES IT.

For more info please visit Manitou website or search google, bing or yahoo. Item Condition The shocks are in good condition with no signs of leaks. Items sold on Ebay http:search.ebay.com/W0QQsassZbikepartscellarQQhtZ-1 Payment I will only accept paypal payments and items must be paid within 5 days of auction end or else item will be relisted. Sorry no exceptions.

Paypal payments will help protect you and I. I will not accept international bids since I cannot guarantee the item will arrive and I cannot track the item. Shipments Items will be shipped USPS priority mail. Since it is easy for me to ship this way. Except for lighter smaller items, I will then ship first class mail. Returns I will only accept returns if the description is drastically incorrect. Condition description is subjective and varies from one person to another person.

Emails I receive as much as 30 emails a day. If I don’t respond right away, please be patient. If I am out of town. I can get as much as 100 emails and that is impossible for anyone to answer all of them. It is more important for me to ship your items as soon as possible.

Then spend a whole day answering emails. Manitou Circus DJ 4X Forks in Black 100mm Travel 20mm Bolt Thru 26 Inch Manitou Forks Manitou Circus DJ/ 4X Forks In black 26 inch They are in great condition Stanchions are mint Travel is 100mm Rebound and compression adjustment Have post mount for disc brakes The steerer is 1& 1/8 size and is 150 mm long They have 20mm bolt through dropouts Nice quality forks Please check my feedback and terms to buy in confidence Feel free to ask questions Please make sure payment reaches us within 5 days. If this is not possible then please get in touch before purchasing so we can come to a agreement I post items from Monday to Friday. Sorry no postage on Saturdays as it effects my riding time. The charges are listed below.

I will not send high value items on a untracked service. Any items paid for by 1pm will be dispatched the same day Insurance. Is included in all quoted prices The item will be posted within 24hrs of payment clearing. If you are at all unhappy with your purchase please before leaving feedback get in touch and give us a chance to rectify the situation We are a small company specialising in high quality mainly pre owned Downhill and Freeride mountain bike parts. Most of our stock is not listed on ebay so if there is something you are after please get in touch. Please feel free to message us through the ask seller question link or if you need to talk to us you can call or text Tel: 79.

Email is niall@fizbiz.biz. Goodbye Cycle Used Manitou Black Elite 80mm 100mm MTB Bike Fork Disc Rim-Brake 26 Vintage Item SKU: 42174 Item Description Scroll up for more photos. Condition& Measurements.three star) tested in good working condition. Lockout works, suspension travel adjusts from 80mm to 100 mm. If you were trying to decide which would be better for your vintage mountain bike build. Why not have both! Steer tube is 236mm long so this will fit most frames.

Manitou Black 2004 Service Manual

Weighs 3lb 14 oz(light for a vintage fork) Manitou New/ Mint Condition: Brand new. May not come with original packaging, may be a new bike take off, never ridden. Five star) Excellent Condition: Very gently ridden. Few, if any, signs of use. Four star) Great Condition: Item is in perfect working condition but has very minor cosmetic imperfections. Three star) Good Condition: Item shows signs of wear. But is well maintained and functions well.

Any scratches. Rub marks, chips, dents, tears, etc.

Will be pictured. Please review pictures closely on two star items. Two star) Fair condition: Item may have major cosmetic flaws. But still functions. Any scratches, rub marks, chips, dents, tears, etc. Will be pictured.

Please review pictures closely on one star items. One star) Goodbye Cycle prefers Paypal or credit card payments over the phone. All in-state residents of Texas will be charged state and/or local sales tax at the time of checkout. Payment must be received within seven(7) days. We reserve the right to file any unpaid cases through eBay. Orders are processed and shipped within 48 hours of payment.

Monday through Friday. Any orders placed Friday will usually ship out the following Monday, occasionally Tuesday. DOMESTIC SHIPPING Specified shipping charges are for the continental US only. Pricing for Alaska and Hawaii on Puerto Rico will be additional for items weighing over 3lbs. We reserve the right to choose the most efficient carrier for your order at the time of shipment. INTERNATIONAL SHIPPING.

The majority of international orders ship. With its super lightweight. Long travel, and now SPV Evolve damping technology for the ultimate in cornering stability and controlled suspension performance, Minute 3 is the best trail fork money can buy.

Specifications: Weight: 4.0 lbs Travel: infinite travel remote. Damping: SPV Evolve. Adjustments: Rebound. SPV Platform Pressure. SPV Volume, Remote ITravel. Lubrication: Semi-Bath with Evil Genius Seals.

Spring: Coil. Casting: Magnesium RA. Stanchions: 30mm Aluminum. Steerer: 1 1/8' CUT to 8.5' 7050 Aluminum. Crown: Hollow Forged Black Aluminum. Color: Black For Disc Brakes.

You are looking at used 2004 model Manitou Black Elite with SPV This is fork has rebuild several years ago and has been sitting around. New dust seal. New oil, grease and whole inside was cleaned. You can see from the photo that dust seal is new and no diets or debris to show it has not ridden since. Steer tube is 8' see photo) Star nut is placed as well( see photo) One big remark is that no decals on fork. I end up removing it hoping to replace it but never got to it while it was available to replace it. Otherwise everything is fine.

Disc compatible and V-Brake studs. Some the scratches from cable rub on crown and some minor scratches on rest of fork. This air fork and one side is SPV which low pressure chamber for automatic lockout technology.

Manual come with it so you can read and setup fork as need it. I have enjoy this fork. Very plush fork. Still have good life left on this fork for more miles on the trail. I was going used on my new frame but I end up buying new fork instead. Due to the nature of products and used we do not take returns on these items.

Download Apple iTunes for Windows. ITunes is a free application for Mac and PC. It plays all your digital music and video. It syncs content to your iPod, iPhone, and Apple TV. Itunes 10.1 for windows xp.

Manitou Service Manual

It is also buyers responsibility to check the safety the products before use. Safety is important and make sure you are comfortable before using it. Ships to US Only. Terms and Conditions: Buyer is responsible for knowing that the item will fit the bike or application. Buyer is responsible for the proper assembly and maintenance of the item.

Buyer agrees to assume all risk and liability resulting from the use of this item. If payment is not received within 7 days(without any form of contact) there is no obligation to hold the item and an Unpaid Item Dispute will be filed. By bidding on the auction or using Buy It Now. You are agreeing to the payment and shipping terms and the terms of the conditions listed above. Feedback will be offered after we receive feedback from the purchaser.

This seller accepts PayPal. Visa, Mastercard, Discover. Payments must be made within 7 days after the sale, if more time is required please email us stating so. Credit cards are accepted through our shop so feel free to contact. Us at: Pedal Power 860-347-3776 ext.1 Insurance is covered within the freight charges.

Manitou Axel Elite 100 Manual

Local pick-up is also available. Pedal Power is a Pro-level retail and service shop that has been named a Top 100 shop for 8 consecutive years.

Located at 359 Main St. CT, Pedal Power is Connecticut's premier bicycle retailer.